• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix door hinge a Loose upvc door hinge replacement Hinge

Fixing a loose door hinge is a simple task for the majority of homeowners. But, if the screw holes are damaged and won't hold screws you might have to use dowels and wood glue before you can install the hinge.

Brush away any surface corrosion. This will help keep the dowels in place and give them a solid foundation to hold onto.

Take the Hinges off

Most hinges on doors can be removed, which makes it easier to move the door from one side to the next or take the entire door hinges upvc off the frame if need be. Removing the hinges is fairly easy for anyone with patience, but you need to know how do it right.

If the hinges have been painted it is necessary to remove the paint before you attempt to remove the pins. If you don't, the paint could be smashed off and scratch your door when you attempt to lift it. Place the hinges into a stainless steel pot and fill it with water to the point that the hinges are completely submerged. Let the hinges rest in the pan for about 30 minutes. The heat from the water will soften the paint making it easier to take off.

Once the pins are loosened, you can remove the hinges from the door and frame. You can make use of a screwdriver to get the job done, however it is recommended that you use a magnetic screwdriver for this task. This type of screwdriver was designed to pick up screws made of steel and make the task run much more quickly.

Before you attempt to remove the hinges it is recommended to spray them with oil. A simple lubricant can make the process move along quickly and help you remove the pins and screws. This kind of lubricant can be found in most hardware stores as well as home improvement shops.

The number of hinges required will also differ based on what type of door you have and the way it's installed. Doors with a heavier core and solid-core will need more hinges, while hollow-core doors with a lighter weight might only require two or three hinges.

It is also essential to understand the different types of hinges to determine which ones will work best in your situation. Exterior hinges are generally designed to support the door's weight, while interior hinges will need to be able to handle heavier loads.

Reattaching the Hinges

Sometimes, the hinges on doors become looser over time and begin to hang in a crooked manner or slide. This can cause problems, but it's usually easy to solve. A simple tightening can solve the issue. If the screw holes have been ripped out, it can be difficult to do. However, there is a trick to get these holes back to their original size that utilizes a wood dowel.

Start by drilling the hole with a drill bit close to the new screw size (normally 3/8"). Then, you can use a wood glue as well as dowels made of wood to fill the hole. To ensure a tight fit, the dowel should be cut at the same length as the screw. After that, reinstall the screw and tighten it to the desired tightness. If the door continues to have the tendency to be bowed and close, then you can add another dowel to the gap and repeat the process. Close the door slowly after each adjustment to ensure that the perimeter clearances are in order.

Another option is to just use a wood plug instead of a dowel. It will work equally well, but may take a bit longer to set up. You can use the wood piece which has been cut to the right size. If you don't have a woodworking instrument, you can use toothpicks or matchsticks made of wood.

Make use of a countersink in order to make the hole smaller for the head of the screw after you have installed it. This will stop the screw from rubbing against the edge of the doors when they are opened and closed. This will aid in tightening the screw after you are reinstalling the hinge.

After you have reinstalled the hinge, make sure to grease it with a dry lubricant to ensure that it doesn't get stuck in the future. Products such as PB Blaster or Liquid Wrench are excellent options. Apply a thin coat and allow it to take approximately 15 minutes to reach the hinge barrel.

Refinishing the Hinges

If you're unsure whether to replace hinges, you could try a few fixes. Check that the screws that secure the hinge plate in place to the door frame and frame are tight. If they're loose, tighten them using an electric drill or screwdriver. Be careful not too tighten the screws, because this could create gaps at the trim joints, or worse, strip the threads.

If you're experiencing issues because the hinge plates are separating from the door and jamb and jamb, you can fix them by applying wood glue to the plate's back and then inserting toothpicks or wooden dowels into the holes. Dowels and toothpicks create a solid base for the screws, and prevent the plates from shifting as you push them in. Let the glue dry before reattaching your hinge.

Another reason that causes hinges that are loose is that the screws are stripped or missing. You can fix this problem by replacing the screws with longer ones. Make sure you use the correct drill bit for the size of the screw hole in order to avoid drilling into other parts of the hinge or jamb.

Close the door once you have reattached your hinge and measure the gap between the frame and the repair door hinge. It should be around the thickness of a nickel all around or less if there's a gap caused by a previous door that was not properly hang. This shouldn't be a problem as long as the hinges are installed correctly.

If you find that the hinges are loose, you can try adding an extra thicker shim between the hinge plate and the mounting surface to give an extra inch of space. You could also try taking the hinge pin from the problematic hinge and then pounding it using a hammer to make it tighter or use a new hinge pin altogether. You can also lubricate your hinges using mineral or jojoba oil to decrease friction and help them hold their position. Periodically lubricating your hinges can help keep them from becoming stiff or squeaky, and can also extend their life.

Cleaning the Hinges

A hinge's continuous movement causes friction, which attracts dust particles. Without regular cleaning and lubrication, these particles get stuck in the moving parts of a hinge for doors and then build up over time. In the end the hinge can become stiff and creaky, and its appearance can get worse. Regular cleaning, lubrication, and inspection can preserve the quality of hinge on a door and ensure its proper operation.

Examine the hinges for signs of the accumulation of rust. If the rust is so bad that it has damaged the surface of the screw holes or the barrel of the hinge, you'll need to replace the hinges. If you can save the hinges, remove any loose rust using wire brush and steel wool. Then apply a rust remover from a commercial store or a homemade solution, such as lemon juice on the hinge. Allow the rust-removing solution to sit on the hinges for several minutes in order to penetrate and dissolve the remaining rust.

Retightening screws can help restore hinge function If you don't wish to spend money or time to replace hinges. If you've sanded the screws however, it might be necessary to add an wooden dowel or shim to the hinge. Dowels made of wood are square pieces of wood that are in the form of rods which are available in varying lengths and sizes. They are available at home improvement stores or woodworking supply shops, or online.

A shim can also be made from a piece of plastic or metal, based on the type of hinge you have. To make a dowel, you need to cut a wooden dowel to the desired length. You can then dip a dowel in carpenter's glue and place it in the hole. The glue will secure the dowel in place.

Before cleaning the hinges, put down a cloth or towel to shield your flooring from spills. After the area has been secured, proceed to clean the hinges using an absorbent sponge or a soft cloth coated with a mild cleaner or vinegar to eliminate dirt, grime, and tarnish. A toothbrush or small brush can be used to access difficult-to-reach places in crevices and tight places.