• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat van key replacement 500 Key Fob Won't Work

A key fob from fiat stilo key 500 is a convenient way to open the doors and begin the car. There are a variety of reasons why the fob may stop working. It could be due to a dead battery, damaged receiver module, water damage issues, and interference.

This listing is for a NEW replacement fiat 500 Electric key Flip Key Remote - like the Ilco brand that must be professionally programmed by a local automotive locksmith (click here to search for a Locksmith Search). Includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the main cause of your 500 key fob not working. Modern key fobs operate with a limited operating range, and should be within just a few feet of the vehicle to function. If you're far from your vehicle and you push the keyfob button it won't respond and display the message "Key Fob Not Detected".

If this occurs then replace the battery for your coin-cell (Part Number CR2032) by a brand new one of a reliable brand, such as Panasonic Duracell or Energizer. You can find them at your local hardware store or on the internet.

After you've replaced the coin cell battery, you can test it by standing next to your fiat car keys cut 500 and pressing the buttons. The car should flash its parking lights, and the key fob should work the lock and unlock buttons.

If the key fob doesn't work after replacing the battery, it may be damaged by water, which prevents it from connecting to the receiver module inside your car. Water damage can happen in a variety of ways, ranging from small splashes to submerging your fob in salt water at the beach. If you believe your fob was exposed to water, you can place it in a rice bag to draw out the moisture. If this doesn't work, the fob might require reprogramming by an experienced auto locksmith or by the dealer.

Water Damage

Water damage can occur when you immerse the fob in the ocean, or wash it in a machine. Saltwater can cause the circuit board to short, and eventually end up dying. In the event that you let your fob get wet, it's not an option but if you accidentally drop it in an empty cup of water, or forget to take it out of your pants pocket before running the washing machine, don't give up hope.

First, remove the battery from the fob. Clean the electronic chip using isopropyl alcohol or another similar product and dry it thoroughly before replacing the battery. Test the fob next to determine if it's functioning. If the key does not work, it may have to be changed. This is usually done by an auto locksmith or dealer.

If the key is older and has never been programmed to your vehicle it is likely to need to be replaced completely. A professional automotive locksmith can do this job. The locksmith will need to cut the key to match the ignition of your vehicle. They'll also need to program the fob into the system of your car. This is a cheap and quick procedure that can be completed on the same day.

Receiver Module Issues

The 500 key fob you have may not function because it's out of range. The remote has a maximum range of 30 feet. Therefore, if you are too far away from your vehicle it won't be able to respond to your commands. This can be fixed by moving it closer to your vehicle until it starts responding.

If you've replaced your coin battery (commonly called a "button" or "watch") and the fob isn't working it could be due to an internal circuit board problem. In the majority of cases, reprogramming your fob will fix the issue. You can find directions on how to do this for the majority of vehicles by searching YouTube or looking through the owner's manual.

It is possible to replace the clips made of metal that hold the coin batteries in place. If they become loose, it may prevent your battery from being properly seated, causing your remote to malfunction.

In rare instances it is possible that the fob will become disconnected from your vehicle due to software problems or hardware issues. This issue can be fixed by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances they may have to install the software again in your body control module, too.

Interference

In addition to a dead coin battery The key fob might not be able to transmit or receive an signal due to interference. This is possible when the key fob is in proximity to an electronic radio transmitter (cell phones or radar detectors) or another source of electromagnetic radiation. Other reasons why the key fob could not function could be due to a weak connection to the buttons, damage to the internal chip, or water damage.

If your key fob suddenly stopped working, or you've tried everything at home to resolve it (e.g. replacing the battery, reprogramming it and using the spare key fiat 500 key fob, it could have a defective receiver module on your 500. The receiver module is situated under the dash and receives the radio frequency signals from the fiat ducato key fob. It then converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy way to reset every single system on board in your 500 device, including the key fob. Disconnect the battery of 12 volts for about 15 minutes, by disconnecting the negative cable first then the positive cable. Reconnect the battery. This will remove any remaining electric current, and also restart the car's computer. This will help you get your key fob to work again. If the issue persists you should seek out an expert certified technician. They will be able to determine the exact cause of issues.