• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps let your pet move around whenever they want, without you having to let them in or out. They also can help stop your cat from peeing in the home.

It is much easier to put an animal flap on a upvc panel than a glass one but you'll require some knowledge and right tools.

Measure the Door

Installing a cat door into the front door is difficult, but as long as the cat flap is the right type and you follow the directions you can make it less difficult. We will be showing you how to mark out the shape, using a jigsaw to cut out the door's area and then finish off the job by securing the cat flap to the door. This will ensure that the flap stays in place and protects the door from rain and wind causing damage.

To determine the size of the cat flap you require, measure your pet's width. This will ensure that the flap is big enough that your pet can go inside and out of the house without having to open and close the door each time, but also small enough to stop them from going too far in either direction.

Once you have the measurements you can determine the area on the door where the template should be placed, usually, this is done using an X, but some kits come with an illustration that outlines where to drill, if yours does then stick it to the door and use a pencil to draw around the door. If your door has moulding or a sill at the bottom, make sure that you leave enough space between your cat and these elements.

Then put on your eye protection and a dust mask. Then using a jigsaw, begin to cut along the line that you've drawn in, don't try to push the blade too hard because this could make it cut faster than you would like it to. If you have a set square then make use of it to verify that you are cutting correctly and also to ensure that the hole is in a rectangle. Once you are satisfied with the shape, you can begin to remove the remaining door material.

Draw a Line

The cat flap lets you to let your pet inside and out without having to worry about unwanted visitors or unwelcome gifts. It also reduces drafts and helps to keep the temperature inside your home steady. However, putting the cat flap to your door could be an intimidating task for those who haven't done it before. This can lead many to hire a professional carpenter or joiner to do the job. While this is certainly an option, it is possible to do the job yourself if you have the right tools and follow the instructions carefully.

While this is much simpler with a wooden door, it is still possible to do this in uPVC doors, though you must be cautious not to damage the doors, as this can cause damage to the warranty. The first step in the process is to measure the door and ensure that it is able to accommodate the new cat flap. This isn't too difficult if you are using a standard uPVC door, but you may need to take more care if you have a composite or other type of door since these can be more difficult to cut than solid upvc door panel with cat flap panels.

Next, you will need to determine the belly height of your cat. This is the height between the floor and the bottom of your cat's stomach. It is important to find an area at the entrance that allows your cat to comfortably pass through. Once you have this information then you need to mark out the area with an eraser and a spirit level so that you can ensure that the hole you make will be suitable for your cat.

Once you've marked the area, it is time to cut out the hole. You will need to use a jigsaw and it is crucial to be patient to ensure that the cuts are clean and smooth, rather than rough and uneven, as it could cause damage to your door. Wear safety glasses and a dust mask when working with the Jigsaw. Inhaling sawdust can be harmful for your health. After you've cut the hole, you will need sandpaper to smooth the edges so that the cat flap can be easily fitted into place.

Cut a Hole

It can be a challenge to fit a cat flap into a door panel or sealed double glazing cat flap glazing unit. If you are not very proficient in DIY, it is best to employ a professional to do the job for you. A mistake in the process may not just be ugly, but also a security risk as well as allowing cold air to enter when the cat is outside and hot air to escape when inside.

The hole's location should be marked on the door using the help of a pencil and a spirit level. This will ensure it is properly positioned and runs flush with the door's other parts. Make sure you have an sandpaper piece on hand for any rough edges.

After the line is traced, you must cut the hole with a jigsaw. Be sure to wear any safety equipment for cat flap In upvc door panel working with the power tool. If you're concerned about the noise, you can purchase an electric jigsaw that is more quiet and easy to use.

It is essential to only remove the material required for the fitment of the cat flap. A small amount of material will be required for the thickness of the the flap, but removing more than this can cause problems and even damage the doors frame.

If the upvc door has a metal panel or frame, it could interfere with the microchip flap. In this case you'll need to make an oversize hole to ensure that the metal doesn't touch the walls of the flap.

If you're planning to install a cat flap inside windows made of double-glazed or upvc with frames made of metal you'll need to talk to a specialist. They can provide you with a brand new piece of glass that has the hole that is already designed for the cat flap. It is much less expensive to get this done rather instead of trying to install the cat flap onto an existing glass pane that hasn't been designed specifically for the purpose.

Fit the Flap

Cat flaps give your pet the freedom to come and go whenever they like and let them relax in the house when they'd like. If you've got a uPVC door cat flap in upvc door panel it can be difficult to fit a cat flap, especially when you don't have glass panes that can be cut to accommodate one. If you are willing to install a half-glazed uPVC replacement panel, it's possible to add a cat flap. It's not as simple as cutting a hole in the door though and there are a few things you'll need to take care of first to ensure that it's safe.

A composite, uPVC or GRP door panel is typically comprised of a plastic skin that is bonded to an insulating polystyrene core. The material is extremely fragile and care should be taken when cutting through it to avoid damaging. This kind of door typically includes a template which you can use as a guide to cut the hole into the door.

Once you've marked the hole in your front door, it is time to put in the cat flap. You can purchase and install various models including basic button operated ones to microchip activated units that allow access only to your pet. Whatever kind of cat flap cover for winter flaps you select, it's vital that your cat flap in Upvc door panel (click4R.com) can use the flap without getting stuck in bad weather.

A circular fitting cat flap in upvc door panel is more effective than a square, because circles can be cut more securely into glass. It's because square holes are more likely to crack the glass when drilled. It's also a safer choice to use since you're not putting yourself at risk by having to drill into toughened glass that could shatter and cause injury to your pet or your family. This is particularly important if there are elderly or children at home who could be injured by glass fragments.